How does a combined cycle power plant work? Explained
Short answer
A combined cycle power plant runs a gas turbine and a steam turbine from the same fuel source. The gas turbine makes electricity first, then its hot exhaust heats water in a heat-recovery steam generator, and the resulting steam drives a second turbine. This reuse of waste heat can raise electrical output by up to 50 percent compared with a simple-cycle plant.
Key points
- Gas turbine exhaust, which would otherwise leave through the stack, is routed through a heat-recovery steam generator.
- Live steam temperatures are typically 420 to 580 degrees Celsius.
- Condenser cooling water can be as cold as 15 degrees Celsius.
- A two-on-one layout uses two gas turbines, two heat-recovery steam generators, and one steam turbine.
How does a combined cycle power plant work? It uses one fuel source to run two linked power cycles. A gas turbine burns fuel and drives a generator, then its hot exhaust passes through a heat-recovery steam generator. That heat turns water into steam, and the steam drives a second turbine and generator. The plant therefore captures energy that a simple-cycle plant would send up the exhaust stack.
A combined-cycle power plant links two heat engines so both use heat from one fuel source. On land, the common form is the combined-cycle gas turbine plant, often called a CCGT plant. It is usually classed as a gas-fired power plant, though some units can also burn diesel. With both turbine types, such a plant can raise electricity output by up to 50 percent from the same fuel compared with a simple-cycle plant. It uses two turbines: a gas turbine and a steam turbine.
For a comparison with fission-based generation, see How does a nuclear power plant work: from fission to grid. For systems that balance variable renewable output, see Smart grids and sustainable energy: renewable support and How does battery energy storage work? A practical guide.
How does a combined cycle power plant work in two stages?
The first stage is a gas turbine cycle. Air is compressed, mixed with fuel, and burned. The hot gas expands through the gas turbine, which turns a shaft connected to a generator. Some of the turbine work also drives the compressor. The exhaust gas leaves the turbine at a high temperature, about 600 degrees Celsius. That exhaust is not waste in a combined-cycle plant; it is the heat source for the next stage. Natural gas is a common fuel, and diesel is another option in some designs.
The second stage is a steam cycle. The heat-recovery steam generator sits between the gas turbine exhaust and the stack. It is a heat exchanger, not a furnace in normal operation. Hot exhaust flows over tubes that carry water and steam. The water is heated, boiled, and often superheated. Live steam temperatures are usually between 420 and 580 degrees Celsius. The steam then leaves the heat-recovery steam generator and enters the steam turbine.
How waste heat becomes steam
The heat-recovery steam generator captures heat from the gas turbine exhaust that would otherwise leave through the stack. Because it recovers heat that would otherwise be lost, the plant gains output without burning extra fuel in the main cycle. The steam conditions depend on the gas turbine exhaust temperature, the heat exchanger design, and the desired steam pressure. In normal operation, the heat-recovery steam generator does not add fuel; it transfers heat from one fluid to another.
The steam turbine is the second heat engine. High-pressure steam expands through it and turns another generator. After expansion, the steam enters a condenser. Cooling water removes heat and turns the steam back into water. That water is pumped back to the heat-recovery steam generator. Cooling water for the condenser can reach 15 degrees Celsius when sourced from a lake, river, sea, or cooling tower. A lower condenser temperature improves the steam cycle because it increases the pressure difference across the turbine.
Supplementary firing and plant flexibility
Supplementary firing adds fuel in the duct of the heat-recovery steam generator. It raises exhaust temperatures from about 600 degrees Celsius to 800 or even 1000 degrees Celsius. Duct burning raises flue temperature and can increase steam flow or temperature. Steam conditions can reach 84 bar and 525 degrees Celsius. It helps the plant follow changes in electrical demand, since duct burners can run efficiently at partial load. It can also increase steam production to cover the loss of another unit. Coal can also serve as an economical supplementary fuel in the steam generator.
Running without supplementary firing gives higher overall thermal efficiency in most combined cycles. Supplementary firing does not improve overall efficiency in most combined cycles. Its main attraction is flexibility: load response, steam production, and continued operation during equipment problems. Flexible operation can improve safety on a ship because the plant can keep running after equipment failures. For a single boiler, firing to 700 to 750 degrees Celsius can raise efficiency. For multiple boilers, flexibility is the major attraction.
Layouts, scale, and operating cost
A common layout is the two-on-one system. In that arrangement, two combustion turbine generators work with two heat-recovery steam generators and one steam turbine generator. During the first cycle, natural gas or diesel fuel burns to drive the two gas turbine generators. Each gas turbine has its own heat-recovery steam generator. The two heat-recovery steam generators feed one steam turbine. This layout concentrates steam generation and can reduce the number of steam turbines needed for a given gas turbine capacity.
Other plants use one gas turbine with one heat-recovery steam generator and one steam turbine, or several independent single-shaft units. The overall plant size and the number of gas turbines required can determine which arrangement is more economical. A group of single-shaft combined-cycle plants can cost more to operate and maintain because it contains more equipment. Yet it can reduce interest costs by allowing a business to add plant capacity only when needed. A multi-shaft or two-on-one plant may suit a large, steady load, while smaller or phased projects may favor separate units.
Cogeneration and low-temperature heat
Combined-cycle units can also supply low-temperature heat for industrial processes, district heating, and other uses. This arrangement is called cogeneration, and such plants are often called combined heat and power plants. In that mode, the plant sells or uses heat that would otherwise be rejected. The electrical efficiency may be lower than in power-only operation, but the total useful energy output can be higher. This makes combined-cycle technology useful where both electricity and heat are needed.
Efficiency, cooling, and limits
Efficiency depends on temperatures, pressures, and cooling. Higher gas turbine exhaust temperature and higher steam temperature improve output, but materials and cooling water set limits. The condenser must reject heat, so the plant needs a reliable cooling source. Lakes, rivers, seas, and cooling towers commonly provide this cooling water. Supplementary firing can improve steam conditions but does not automatically improve overall efficiency. The best design matches the gas turbine, heat-recovery steam generator, steam turbine, and cooling system to the expected duty.
| Item | Typical value |
|---|---|
| Live steam temperature | 420-580 C |
| Condenser cooling water | As low as 15 C |
| Gas turbine exhaust before supplementary firing | About 600 C |
| Exhaust after supplementary firing | 800-1000 C |
| Steam condition with duct burning | 84 bar, 525 C |
Questions people also ask
What is the main advantage of a combined cycle power plant?
It produces up to 50 percent more electricity from the same fuel than a simple-cycle plant by using gas turbine exhaust to make steam.
What is an HRSG?
A heat-recovery steam generator is a heat exchanger that captures exhaust heat from a gas turbine and uses it to heat water and produce steam.
Does supplementary firing improve overall efficiency?
No, in most combined cycles it does not raise overall efficiency; it mainly improves flexibility and steam production.
Can a combined cycle plant provide heat as well as electricity?
Yes, in cogeneration mode it can supply low-temperature heat for industrial processes or district heating.
Related pages
- Electricity transmission over long distances
Electricity transmission moves bulk power from generation sites to substations using high voltage, transformers, and interconnected lines. Raising voltage reduces current and resistive losses, while overhead and underground routes involve different costs, visibility, and repair trade-offs. Grid operators manage these networks, interconnections, and faults to keep power flowing across regions.
- How do solar panels generate electricity?
Solar panels turn sunlight into electricity mainly through the photovoltaic effect in silicon cells. The cells produce direct current, and an inverter changes it to alternating current for home use. A second method, thermal conversion, uses heat and steam to drive a turbine.
- What is baseload power and how it works
Baseload power is the minimum amount of electricity the grid must supply at any moment. It is usually met by plants that can run steadily for long periods, while faster plants handle short peaks.
- How does a coal fired power plant work?
A coal-fired power plant burns coal to boil water, makes high-pressure steam, spins a turbine, and drives a generator. The steam is cooled and returned to the boiler, while ash and other pollutants are controlled before release.
- Power Plant Cooling Towers: How They Work
Power plant cooling towers remove waste heat from condenser water so steam can be condensed and reused. Wet cooling towers use evaporative cooling, while water losses are replaced with makeup water and controlled with blowdown. Their size and draft method depend on plant capacity and site conditions.
- How Does a Hydroelectric Power Plant Work?
A hydroelectric power plant uses the energy of moving or falling water to spin a turbine and turn a generator that produces electricity. Water is usually stored behind a dam, released through a penstock, and returned to the river through a tailrace. Output depends on both water flow and the elevation change, or head.
How this page was prepared
Before writing, the topic was researched in the sources below. The page then passed automatic quality checks.