Undersea Fiber Optic Cables: How They Work
Short answer
Undersea fiber optic cables are armored cables full of glass strands, laid on the seabed to carry nearly all international internet traffic between continents. Signals travel as light, boosted by repeaters that draw power from the shore, and the design has to survive pressure, salt water, anchors and trawler gear for decades. When a cable does break, traffic reroutes and a repair ship splices the fibers back together at sea.
Key points
- Between about 95 and 99 percent of international internet traffic crosses the ocean on fiber cables rather than satellites.
- A submarine cable combines steel wire armor, a polyethylene sheath, water-blocking gel and a copper power conductor around the optical fibers.
- Ultra-low-loss fiber at 0.17 to 0.18 dB/km lets a span run 150 to 300 km before it needs a repeater.
- Specialized cable ships lay the cable, and shallow sections are buried where anchors and fishing gear are a threat.
- Most faults come from human activity, and repairs are done at sea by grappling the cable, splicing the fibers and lowering it back.
What undersea fiber optic cables carry
Undersea fiber optic cables are the glass lines laid across the ocean floor between landing stations on separate continents, and they move nearly all international internet traffic. Published figures for their share of that traffic sit between roughly 95 and 99 percent, with satellites handling the remainder. Send a message to another country and the odds are strong that it leaves your device, reaches a coastal landing station and then travels as pulses of light along the seabed.
A cable is not one fiber. It holds several pairs, and each pair works as a two-way link: one strand carries traffic out, the other carries it back. TAT-8, the first transatlantic telephone cable built around optical fiber, entered service in 1988 with two working pairs and a third held in reserve. Later systems added more pairs and put many separate wavelengths on each strand through dense wavelength division multiplexing.
What is inside a submarine cable
The glass sits at the center of a layered structure. Each layer outward does a specific job against the seabed environment.
| Layer | Material | Job |
|---|---|---|
| Outer sheath | Polyethylene | Blocks seawater corrosion and abrasion |
| Armor | Two layers of steel wire | Resists anchors, trawler gear and seabed drag |
| Water blocking | Gel | Stops a leak from spreading along the length |
| Power path | Copper conductor | Feeds electricity to the repeaters |
| Core | Optical fibers in petroleum jelly | Carries the light signal |
Ordinary outdoor cable fails underwater. It has too little armor, water travels along the core once the sheath is nicked, and hydrostatic pressure crushes the structure. Submarine designs are rated for depths of up to 8,000 m and for decades of immersion. Where a route crosses fishing grounds, shipping lanes or shallow shelf water, the cable is buried beneath the seabed instead of being left exposed. Deep sections, where trawlers rarely work, are simply laid on the bottom.
Why submarine fiber is engineered to lose less light
Signal loss sets the distance a link covers before it needs amplification. The glass in submarine cable is ultra-low-loss single-mode fiber: it loses only 0.17 to 0.18 dB per kilometer at 1550 nm, while ordinary G.652.D fiber loses about 0.22 dB per kilometer at the same wavelength. Across an ocean crossing that difference decides how many amplifiers a system needs, and every amplifier adds cost, power demand and a component that can fail.
Two fiber families show up in submarine builds: G.654.D, a cut-off shifted design tuned for DWDM channels in the C and L bands near 1550 nm, and named submarine products such as Corning Vascade and OFS AllWave Fulfillment. The payoff is an unrepeatered reach of 150 to 300 km, which cuts the number of powered repeaters on a route. The physics of moving data as light is the same as in how fiber optic communication transmits data; submarine systems just push it to the limit of what glass allows.
How a cable is laid on the seabed
- Survey the route with sonar and seabed mapping to avoid canyons, wrecks, pipelines and unstable slopes.
- Load the cable into the ship's tanks, often in one continuous length.
- Pay it out over the stern under controlled tension so it follows the seabed contours without kinking.
- Bury the shallow-water sections with a plough or a jetting tool.
- Bring the end ashore and splice it into the landing station.
Cable ships such as Orange Marine's René Descartes are built for this work, with the tension machines and splicing equipment needed to handle thousands of kilometers of heavy cable in open water.
How the repeaters are powered
A transoceanic cable cannot rely on the signal alone. Repeaters sit at regular intervals along the route, each one an optical amplifier that boosts the light without converting it back into an electrical signal. Amplifiers still need power, and there is no power source on the seabed.
Electricity comes from the shore. A high voltage is applied to the copper conductor inside the cable, and current flows along the whole length of the system, feeding each repeater in series as it passes. That conductor is why the cable behaves as a single electrical circuit: a break in the copper takes the segment down just as a break in the glass does.
How cables break and how they are repaired
Most faults are caused by people. Ship anchors and trawler gear account for the bulk of the damage, and seabed abrasion wears cables down where they lie exposed. Early fiber cables also had trouble with shark bites, which strengthened the case for the steel wire armor used today. Natural events such as underwater landslides and earthquakes cut cables as well.
Concentration matters as much as the raw number of faults. In 2008 several cables were cut at the same time, showing how exposed the network is at choke points where many routes share one corridor. In 2022 cables near the Faroe and Shetland Islands were damaged and Mediterranean cables were also cut. In November 2024 two cables failed within 24 hours, and the pattern raised fears of sabotage.
Repair follows a fixed routine. A repair ship locates the fault, grapples the cable, cuts it and lifts one end to the surface. Technicians splice the fibers with a fusion splicer, test the joint, and lower the cable back with enough slack for it to settle on the seabed. One repair can take days or weeks, because the ship has to reach a remote position and rough weather stops work.
Undersea cables versus satellites
Satellites cannot match fiber on bandwidth or delay. A geostationary satellite sits about 35,786 km up, so a signal travelling to it and back covers roughly 71,000 km, which adds a lag anyone on a call will notice. Light in fiber covers a far shorter path across the ocean, and one cable carries more traffic than a satellite can. That is why satellite internet serves ships, aircraft, remote islands and backup routes, while the main traffic between continents stays on the seabed.
From the beach to your phone
A cable ends at a landing station, where the fibers are terminated and joined to terrestrial networks. From there the traffic runs on land fiber to data centers and internet exchange points, and the last stretch to a phone or laptop often goes over a mobile network. The radio side of that final hop is covered in how cell towers work. The ocean crossing is one hop among many, but it is the hop that makes a call between continents feel local.
Questions people also ask
How much of the internet goes through undersea cables?
Almost all of it. Quoted figures usually fall between about 95 and 99 percent of international traffic, with satellites covering the rest, mainly for remote regions, ships and backup capacity.
How deep do undersea cables go?
Submarine designs are pressure rated for depths of up to 8,000 m. In shallow shelf water and fishing grounds the cable is buried under the seabed, while in deep water it lies on the bottom.
What causes most undersea cable damage?
Human activity, above all ship anchors and fishing gear, followed by seabed abrasion, landslides and earthquakes. Early fiber cables also suffered shark bites.
How long does it take to repair a broken cable?
Anywhere from days to weeks. A repair ship must reach the site, grapple the cable, lift it, splice the fibers and lay it back down, and bad weather can suspend the work.
Why not use satellites instead of cables?
Bandwidth and latency. A geostationary satellite adds a round trip of roughly 71,000 km and carries far less traffic than a single cable, so satellites fill gaps rather than replace the seabed network.
Related pages
- Circuit Switching vs Packet Switching Explained
Circuit switching reserves a fixed path and its bandwidth for one session, so delay stays predictable but capacity sits idle when the session is quiet. Packet switching splits data into independently routed packets that share links, so bandwidth is used more efficiently and the network scales well, while queuing can add delay, reordering, or loss. The better choice depends on whether the traffic is steady and time sensitive or bursty and varied.
- Radio frequency spectrum allocation for telecommunications
Governments designate frequency bands for defined radio services and set sharing conditions, then license individual stations or networks to use those bands under technical limits. International coordination through the ITU Radio Regulations keeps national tables compatible across borders, while in the United States the FCC manages non-federal use and NTIA manages federal use.
- How cellular roaming works: towers, handoffs and costs
Your phone roams when it cannot use its home carrier and instead registers on a partner or foreign network that has an agreement with that carrier. Tower handoffs move the active connection between cells as you move, while roaming moves the relationship itself to a visited network while the home account still works for calls and data. Costs and controls depend on the plan, so Wi-Fi calling and day passes matter before you travel.
- SIM vs eSIM: How Physical and Embedded SIMs Differ
A physical SIM is a removable card that holds your carrier credentials, while an eSIM is a chip built into the phone that receives its profile remotely. The two connect you to the same networks, but they differ in how fast you can switch plans, how many lines one device holds, and how the line behaves if the handset is lost. Which one suits you depends on whether you value instant digital switching or the ability to move a card between phones.
- How VoIP Works: Voice over Internet Protocol Explained
VoIP (Voice over Internet Protocol) carries phone calls as data packets over the same networks that deliver web traffic, instead of holding a dedicated copper circuit open for the conversation. Your voice is sampled, compressed by a codec, addressed, and routed across the internet, then reassembled and played back at the other end. Because it rides on broadband you already pay for, it costs less than a traditional line and works from a desk phone, a laptop, or a mobile app.
- How Satellite Internet Works: Technical Guide
Satellite internet routes user traffic by transmitting signals between local antennas, orbital spacecraft, and ground stations tied to the internet backbone. Modern low-Earth-orbit constellations use high-frequency radio beams and optical inter-satellite laser links to pass data across space with low latency. Ground stations complete the loop by pulling web traffic from land-based servers and transmitting it back into orbit.
How this page was prepared
Before writing, the topic was researched in the sources below. The page then passed automatic quality checks.