Robotics
Robotics combines mechanical engineering and computer software to build programmable machines that manipulate physical objects and navigate physical spaces. The commercial industry began in 1961, when General Motors installed the Unimate arm to handle hot die castings. Current systems range from rigid Cartesian pick-and-place gantries operating at micrometer tolerances to autonomous mobile platforms running localization algorithms across warehouse floors.
This category covers the engineering principles behind mechanical movement and automated control. Articles explain inverse kinematics, detailing how to calculate joint angles from a target coordinate using geometric and matrix-based methods. Other guides detail degrees of freedom in kinematic chains, as well as the mechanical output differences between hydraulic drives and brushless electric motors.
Software resources explain framework standards such as the Robot Operating System (ROS), examining how computational nodes exchange sensor data and motor commands over publish-subscribe networks. A six-axis arm requires different kinematic solvers and actuator pairings than a differential-drive mobile base. The entries below provide the mathematical models and hardware specifications necessary to evaluate these mechanisms.
Latest pages
- PID Controllers in Robotics: How Motion Control Works
PID controllers in robotics compare a target motion with measured motion and combine proportional, integral, and derivative corrections to calculate a control command. The robot applies that command to a motor or other actuator, then repeats the measurement and correction as new sensor data arrives.
- Uncanny Valley Robotics: Why Humanlike Robots Feel Creepy
The uncanny valley is a hypothesized drop in human affinity toward an artificial figure that looks almost, but not quite, human. Masahiro Mori proposed the relationship in 1970, and controlled face-rating studies have since confirmed a robust dip in likability, with weaker and more context-dependent effects on trust. Robot designers avoid it by matching realism across features, keeping appearance stylized, and adding baby-like or cartoonish traits.
- Collaborative Robots vs Industrial Robots: Key Differences
Industrial robots are built for speed, heavy payloads and micron-level repeatability inside a fenced cell, while cobots are built to work next to people, move between tasks and be programmed by hand. The choice usually comes down to part weight, how often the job changes, and how quickly the purchase pays back. Most factories that use both keep cobots at assembly and inspection and industrial arms at stamping or palletizing.
- Robotic End Effectors: Types and Applications
Robotic end effectors are the tools attached to the free end of a robotic arm, and they are the part that actually grips, welds, paints, drills or measures. They fall into three broad groups: grippers, process tools, and sensors, with the application deciding which one fits.
- Sensors in Autonomous Robots: Primary Types and Uses
Autonomous mobile robots rely on a small set of primary sensors: wheel encoders and inertial measurement units for motion, LiDAR, ultrasonic and depth cameras for range, cameras for vision, and proximity or safety scanners for contact detection. No single device is trusted alone, so their readings are fused into one pose estimate that drives navigation and obstacle avoidance.
- Simultaneous Localization and Mapping (SLAM) Explained
Simultaneous localization and mapping is the problem of a robot entering an unknown environment, building a map of it, and estimating its own position inside that map at the same time. The two estimates depend on each other, so the system solves them jointly as a probabilistic estimation task. The result is a map plus a pose estimate that gets corrected whenever the robot revisits a place it has already seen.
- Robotics Operating System ROS: Architecture and Mechanics
The Robot Operating System (ROS) is an open-source middleware suite that coordinates software and hardware components across robotic platforms. It supplies low-level device control, hardware abstraction, inter-process message exchange, and package management across distributed computer clusters. By decoupling individual software tasks into modular nodes, ROS allows developers to assemble complex robotic behaviors from reusable code.
- Types of Actuators in Robotics and How They Work
Robotic actuators convert electrical, fluid, or thermal energy into physical force and displacement, operating as mechanical muscles for automated systems. Engineers categorize them by their drive mechanism into electric, hydraulic, pneumatic, and piezoelectric systems, as well as by their kinematic output into linear and rotary devices. Selecting an actuator requires balancing torque, operating velocity, positioning accuracy, power consumption, and control protocols.
- How to Do Inverse Kinematics in Robotics
Inverse kinematics calculates the required joint angles of a robotic manipulator to place its end-effector at a specific target position and orientation. Engineers solve this using closed-form analytical methods for standard arm geometries or iterative numerical algorithms for complex and redundant systems. The process bridges Cartesian task requirements with physical motor actuator commands.
- What Are Degrees of Freedom in Robotics? Explained
Degrees of freedom in robotics represent the total count of independent parameters needed to determine the exact spatial configuration of a mechanical system. In three-dimensional physical space, an unconstrained rigid body has six degrees of freedom, split equally between linear displacement and angular orientation. Adding independent joints increases the kinematic flexibility of a robotic manipulator, dictating the volume and dexterity of its reachable workspace.