Wesloo
All topicsTopics

Electronics

Types of Capacitors: Functions and Applications

Short answer

Capacitors divide into fixed and variable, polarized and non-polarized families, and the dielectric material decides most of how each one behaves. Ceramic, electrolytic, film, mica, glass and supercapacitor types cover different capacitance ranges and jobs, from tuning a radio to smoothing a power supply. Picking one comes down to value, voltage rating, stability over temperature and frequency, and package.

Key points

  • Every capacitor is two conductive plates with a dielectric between them; the dielectric material and the plate construction define the type.
  • Electrolytics (aluminium, tantalum, niobium) are polarized and store the most charge per volume, but their capacitance falls sharply at high frequency.
  • Class 2 ceramics and plastic films lose capacitance as frequency rises because of dielectric relaxation in the material.
  • Variable and gang capacitors adjust capacitance mechanically by changing the overlap between rotor and stator plates.
  • Supercapacitors store energy in double layers at the electrode surfaces, giving farads of capacitance at low cell voltage.

Types of capacitors fall into a handful of families, and the family decides almost everything about how a part behaves: its capacitance range, its voltage limit, whether it can be connected either way round, and how far its value drifts with temperature and frequency. All of them do the same basic job. Two conductive plates sit close together with an insulating material, the dielectric, between them, and charge collects on the plates when a voltage is applied. Capacitance is measured in farads, a unit so large that practical parts are marked in microfarads, nanofarads and picofarads.

What is inside a capacitor?

The dielectric can be air, paper, plastic film, mica, ceramic, glass, or a thin oxide layer grown on metal. Capacitance depends on three things: the area of the plates, the distance between them, and the dielectric constant of the material in the gap. Larger plates and a thinner dielectric give a higher value.

Size varies for the same reason. A ceramic disc that tunes a radio receiver is a few millimetres across, while a smoothing capacitor in a power supply can be the size of a drink can. Both store charge. They differ in how much, how accurately the value is held, and how the part behaves over temperature and frequency.

How are capacitors classified?

Three properties sort nearly every part on the market: whether the capacitance is fixed or adjustable, whether the part is polarized, and which dielectric it uses.

Fixed capacitors hold one value. Variable types let the value be adjusted and are usually paired with fixed parts when only a small change is needed. Inside a tuning capacitor, a rotor turns its plates in and out of a set of fixed stator plates, which changes the overlapping area and therefore the capacitance. Two or three sections mounted on one shaft form a gang capacitor, used to tune several circuits together.

Polarization is the second split. Electrolytic parts have a positive anode and must be wired the right way round, because reversed voltage damages the oxide layer. Non-polarized parts work in either orientation, survive AC, and suit circuits with no defined positive and negative rails. They also tend to leak less.

Which types of capacitors are used most often?

The table compares the main families. Ranges overlap between families.

TypeDielectricTypical capacitanceUsual job
Ceramic, class 1Ceramic, stable (NP0/C0G)1 pF to 100 nFTuning, filters, timing
Ceramic, class 2Ceramic, high permittivity100 pF to 100 µFDecoupling, bypass
Aluminum electrolyticAluminum oxide on etched foil1 µF to over 1 FSmoothing, bulk storage
Tantalum electrolyticTantalum oxide0.1 µF to 1000 µFCompact supply decoupling
FilmPolypropylene, PET, PTFE1 nF to 100 µFPulse, AC, precision
MicaMica sheets with metal foil1 pF to 10 nFRF, high stability
SupercapacitorElectrochemical double layerFractions of a farad upwardEnergy storage

Ceramic capacitors

Class 1 ceramics hold their value tightly across temperature and applied voltage, which makes them the choice for tuned circuits and oscillators. Class 2 ceramics pack far more capacitance into the same footprint but lose value with voltage, temperature and frequency, so they go where the exact number matters less: decoupling next to an integrated circuit, bypass paths, and general filtering.

Electrolytic capacitors: aluminum, tantalum and niobium

An electrolytic capacitor gets its high capacitance from a very thin oxide layer grown on a roughened metal anode by anodization. That oxide is the dielectric, and the electrolyte provides the cathode contact. Aluminum is the most common anode material because it is cheap and can be etched to expose a large surface area. Tantalum and niobium versions are smaller for the same rating and suit compact portable designs. Aluminum parts are also sold as surface-mount chips, where they replace tantalum types across certain voltage and capacitance ranges. Typical duties are input and output decoupling in AC supplies, switched-mode power supplies and DC-to-DC converters.

Film capacitors

Plastic film dielectrics give tight tolerances and hold their values longer than most other types, which is why film parts appear in filters, sample-and-hold circuits and audio paths where accuracy matters. Polypropylene is the usual dielectric for power film capacitors. Metallized paper types cover cost-sensitive jobs and serve as carrier electrodes for high AC or high pulse loads. Windings may be filled with insulating oil or epoxy resin to remove air pockets and cut the risk of internal short circuits. Film/foil construction withstands higher surge and pulse voltages than metallized film, but it is larger and has no self-healing behavior, so an internal short can disable the part.

Mica and glass capacitors

Mica capacitors alternate mica sheets with metal foil, and the number of layers sets the capacitance value. They are stable and low-loss, which suits radio-frequency work. Glass capacitors date back to the Leyden jar, which was made of glass. By 2012, glass capacitors were available in surface-mount form for circuits that need very stable and very reliable operation.

Supercapacitors and variable capacitors

Electrochemical capacitors, usually called supercapacitors, contain a pair of electrodes, an ion-permeable separator between them, and an electrolyte that links the electrodes. When voltage is applied, ions in the electrolyte gather at each electrode to form double layers of opposite polarity, storing far more charge than a conventional dielectric can. The trade-off is low voltage per cell and lower energy density than a battery. China is trying out a new type of electric bus that runs without power lines and uses energy stored in large supercapacitors. The capacitors are quickly topped up at bus stops and fully charged at the terminus.

How does frequency affect a capacitor?

Most discrete types lose capacitance as frequency rises. In class 2 ceramics and plastic films the cause is dielectric relaxation: the dipoles inside the material take a finite time to respond, so permittivity falls as the driving frequency climbs.

Electrolytics behave differently and end up worse. Charge in a liquid electrolyte is carried by ions that have to move physically, and their mobility is limited. At high frequency the ions cannot reach every part of a deeply etched anode, so less of the surface contributes to the capacitance. The rougher the anode, the sharper the loss: a low-voltage electrolytic with a heavily etched anode can measure only about 10 to 20 percent of its 100 Hz capacitance at 100 kHz. That matters in a switched-mode supply, where the ripple current sits in the tens or hundreds of kilohertz.

What functions do capacitors perform?

  1. Blocking DC while passing AC. A coupling capacitor links two stages, for example two amplifier stages built around a transistor, and passes the signal while keeping each stage's DC bias separate.
  2. Decoupling and bypass. A small ceramic part next to a chip pin shunts supply noise to ground and supplies brief current surges when the chip switches.
  3. Smoothing. In a rectified supply, a large electrolytic charges on the peaks and discharges between them, which flattens the ripple.
  4. Tuning and timing. With an inductor or a resistor, a capacitor sets the resonant frequency of a radio circuit or the time constant of an RC delay.
  5. Energy storage. Camera flashes and other pulsed loads pull a burst of current from a capacitor instead of straight from the supply.
  6. Signal separation. Filters built from capacitors with resistors or inductors split wanted signals from interference.

How do you choose a capacitor for a circuit?

Work through five things: the capacitance value with a tolerance the circuit can live with, a voltage rating with margin above the highest voltage the part will see, equivalent series resistance if ripple current is involved, temperature coefficient and stability, and the physical package.

Package choice follows the board. Surface-mount chips save space and suit automated assembly, while through-hole parts are easier for hand work and are common in power sections. Getting either type onto a board reliably depends on technique. If you assemble by hand, the basics of electronic soldering technique matter as much as the component choice, and it helps to know how printed circuit boards are made before deciding which package fits your layout.

Values are marked in different ways. Large electrolytics print capacitance, voltage and polarity on the can. Small ceramics and films use short codes, often three digits where the first two are significant figures and the third gives the number of zeros in picofarads, so 104 means 100 nF. Mica types use a color code similar to the one on resistors, which makes reading resistor color codes useful background when you meet a banded capacitor.

Polarity is the mistake that kills parts fastest. An electrolytic fitted backwards, or one operated above its voltage rating, can vent or short. On a board where several capacitors sit in parallel, one reversed part is enough to take down the rail. Check the stripe on the can and the polarity marking on the board before applying power.

Questions people also ask

What is the most common type of capacitor?

Ceramic, especially class 2 multilayer chips, because they are small, cheap and non-polarized. Aluminium electrolytics are the commonest choice when large capacitance is needed in a power supply.

Can I replace an electrolytic capacitor with a ceramic one?

Sometimes, if the capacitance and voltage ratings allow it and the circuit does not need the electrolytic's bulk storage. Remember that class 2 ceramics lose capacitance under DC bias, so the marked value may not be the value you get in circuit.

Why do capacitors lose capacitance at high frequency?

In ceramics and films, the dipoles in the dielectric cannot keep up with a fast-changing field, which lowers permittivity. In electrolytics, the ions in the electrolyte cannot reach the whole etched anode surface in time.

What happens if you connect an electrolytic capacitor backwards?

The thin oxide layer that acts as the dielectric breaks down, leakage rises, gas builds up inside the can, and the part may vent or short. Non-polarized types have no such restriction.

How do I read the value printed on a small capacitor?

Most ceramics and films use a three-digit code in picofarads, where the third digit is the number of zeros: 104 is 100 nF and 223 is 22 nF. Larger electrolytics simply print the value and voltage on the case.

Related pages

  • Microcontroller vs Microprocessor: Key Differences

    A microcontroller is a complete small computer on one chip, with CPU, memory and input/output together, so it can run a dedicated task with almost no extra parts. A microprocessor is a CPU on its own chip that depends on external memory and controllers, which buys speed and flexibility at higher cost and power. Choose an MCU for embedded control and an MPU for general computing.

  • OLED vs LED Display: What Actually Differs

    OLED pixels make their own light and switch off completely, which gives perfect black levels, wide viewing angles and thin panels. An LED display is normally an LCD with an LED backlight, so it wins on brightness, price, lifespan and very large sizes. The right choice depends on the room, the device and how much static content stays on screen.

  • Alternating Current vs Direct Current: Key Differences

    Direct current moves charge in one direction at a steady voltage, while alternating current reverses direction at a set frequency. That single difference decides how each type is generated, how far it can be sent, and why electronics convert AC into DC before use.

  • Basic Electronic Soldering Techniques: Practical Guide

    Electronic soldering joins metallic component leads to printed circuit board traces using a heated filler alloy without melting the workpieces themselves. Successful connections require simultaneous heating of both joint surfaces, proper alloy and flux selection, and undisturbed cooling to form a shiny concave fillet. Solder ensures low-resistance electrical conductivity, while physical wire crimping provides any necessary structural strength.

  • How to Read Resistor Color Codes: Complete Guide

    Resistor color codes use standardized colored stripes on a resistor body to indicate its resistance value in ohms, its multiplier, and its tolerance percentage. To read the code, orient the component so the isolated or metallic tolerance band sits on the far right, then read the colored stripes sequentially from left to right. Four-band resistors provide two significant digits, five-band variants provide three digits for precision, and six-band types add a temperature coefficient rating.

  • How Lithium-Ion Batteries Work: Chemistry and Design

    Lithium-ion batteries store and release electrical energy through the reversible transfer of lithium ions between two electrodes. As a cell discharges, lithium ions travel from the negative graphite anode to the positive metal oxide cathode via an internal electrolyte, driving an electrical current through an external circuit. Connecting an external power source reverses this migration to replenish the stored charge.

How this page was prepared

Before writing, the topic was researched in the sources below. The page then passed automatic quality checks.

Report a mistake on this page